久久8-久久91精品国产91久-久久91精品久久久久久水蜜桃-久久91亚洲精品中文字幕-美女很黄很黄免费的-美女很黄很黄免费

Service Hotline:0510-88700553/88707301

?

PRODUCTS LIST

Service Hotline:

0510-88700553/88707301

News>Position:HOME > News

Vacuum laminating machine in the production process of atten

The problems that should be paid attention to in the production process of coating machine

1, check the density of the board and Lou milling quality. The poor quality of the board, engraving and milling the bottom hair, resulting in the product after coating the surface is not smooth phenomenon.

2, PVC film should be used in the hard film, will not rebound after absorption phenomenon. If the product appears in the phenomenon of valgus, it belongs to the PVC membrane in the composite processing, caused by different pull.

3, the film production adhesive can not have the phenomenon of rebound, so the quality of special glue directly affect the quality of the product. In order to solve the above problems, the workpiece should not be sprayed once and sprayed once. If it is not in place or unclear, it may be the problem of insufficient pressure or engraving and milling quality. If there is varus curl phenomenon, indicating a PVC film problems. If the phenomenon of bonding is not strong, there is a problem with the adhesive. All normal before spraying the official production, the relevant issues may consult the service department or technical service personnel.

maintenance

1, countertops should be kept clean, to prevent dust, sawdust, etc. fall on the work surface. Regularly clean the air filter to prevent blockage, to avoid affecting product quality.

2, the first cumulative use of 100 hours, vacuum pump oil should be replaced, check the vacuum pump oil level every week, the oil level below the cursor 1/3 should be immediately added, the vacuum pump 1 # vacuum pump oil. If oil is found to be contaminated, replace it immediately. Before changing the oil, the vacuum pump must be operated for 30 minutes to make the oil thinner, then stop the pump, let the oil go away, and then open the inlet for 1-2 minutes. At this moment, slowly add a small amount of clean oil from the inlet, To replace the oil chamber of the oil.

3, the equipment stopped running, should release the PVC diaphragm compression device. During normal work, all the equipment shall not be removed to avoid unexpected accidents.

4, in the production process should pay close attention to the operation of equipment, identify problems solved in time. Belongs to electrical failures, should be handled by professionals.

Copyright ◎ 2016 yudajixie.com Wuxi Yuda Light Industry Machinery Factory All rights reserved suICP12031851suICP12031851

主站蜘蛛池模板: 日韩精品欧美在线 | 一级色黄 | 天天综合天天做天天综合 | 亚洲欧美小视频 | 久久青草国产手机看片福利盒子 | 精品视频在线观看免费 | 国产亚洲精品自在久久77 | 香蕉 在线播放 | 夜夜夜操 | 新天堂网| 综合亚洲欧美日韩一区二区 | 97久久天天综合色天天综合色 | 九九精品免视频国产成人 | 黄色欧美网站 | 日本高清在线观看天码888 | 一级毛片免费视频观看 | 亚洲自拍小视频 | 伊人色综合久久天天人守人婷 | 波多野结衣中文字幕一区二区 | 91国内在线视频 | 悠悠色综合 | 在线亚洲综合 | 麻豆视频免费在线播放 | 日本加勒比在线视频 | 日韩精品综合 | 国产丝袜脚 | 日韩一区二区三区四区五区 | 中文国产成人精品久久无广告 | 五月天六月婷婷 | www.91麻豆| 国内精品久久久久久中文字幕 | 韩国毛片免费 | 欧美啪啪精品 | 香蕉在线精品一区二区 | 国产91精选在线观看麻豆 | 99视频精品全部免费免费观 | 亚洲国产精品一区二区三区久久 | 青草草在线视频 | 成人特级毛片 | 欧美黄色高清视频 | 亚洲一区二区精品推荐 |